您的当前位置:首页正文

SN54ABT16640资料

2020-03-09 来源:小奈知识网
元器件交易网www.cecb2b.com SN54ABT16640, SN74ABT1664016-BIT BUS TRANSCEIVERSWITH 3-STATE OUTPUTSSCBS107C – APRIL 1992 – REVISED JANUARY 1997DMembers of the Texas InstrumentsDDDDDDDWidebus™ FamilyState-of-the-Art EPIC-ΙΙB™ BiCMOS DesignSignificantly Reduces Power DissipationLatch-Up Performance Exceeds 500 mA PerJEDEC Standard JESD-17Typical VOLP (Output Ground Bounce) < 1 Vat VCC = 5 V, TA = 25°CDistributed VCC and GND Pin ConfigurationMinimizes High-Speed Switching NoiseFlow-Through Architecture Optimizes PCBLayoutHigh-Drive Outputs (–32-mA IOH,64-mA IOL)Package Options Include Plastic 300-milShrink Small-Outline (DL) and Thin ShrinkSmall-Outline (DGG) Packages, and 380-milFine-Pitch Ceramic Flat (WD) PackageUsing 25-mil Center-to-Center SpacingsSN54ABT16640...WD PACKAGESN74ABT16640...DGG OR DL PACKAGE(TOP VIEW)descriptionThe ’ABT16640 are inverting 16-bit transceiversdesigned for asynchronous communicationbetween data buses.These devices can be used as two 8-bittransceivers or one 16-bit transceiver. It allowsdata transmission from the A bus to the B bus orfrom the B bus to the A bus, depending on the logiclevel at the direction-control (1DIR and 2DIR)inputs. The output-enable (1OE and 2OE) inputscan be used to disable the device so that thebuses are effectively isolated.1DIR1B11B2GND1B31B4VCC1B51B6GND1B71B82B12B2GND2B32B4VCC2B52B6GND2B72B82DIR1234567891011121314151617181920212223244847464544434241403938373635343332313029282726251OE1A11A2GND1A31A4VCC1A51A6GND1A71A82A12A2GND2A32A4VCC2A52A6GND2A72A82OETo ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullupresistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.The SN54ABT16640 is characterized for operation over the full military temperature range of –55°C to 125°C.The SN74ABT16640 is characterized for operation from –40°C to 85°C.FUNCTION TABLE(each 8-bit section)INPUTSOELLHDIRLHXOPERATIONB data to A busA data to B busIsolationPlease be aware that an important notice concerning availability, standard warranty, and use in critical applications ofTexasInstruments semiconductor products and disclaimers thereto appears at the end of this data sheet.Widebus and EPIC-ΙΙB are trademarks of Texas Instruments Incorporated.PRODUCTION DATA information is current as of publication date.Products conform to specifications per the terms of Texas Instrumentsstandard warranty. Production processing does not necessarily includetesting of all parameters.Copyright © 1997, Texas Instruments IncorporatedPOST OFFICE BOX 655303 DALLAS, TEXAS 75265•1元器件交易网www.cecb2b.comSCBS107C – APRIL 1992 – REVISED JANUARY 1997SN54ABT16640, SN74ABT1664016-BIT BUS TRANSCEIVERSWITH 3-STATE OUTPUTSlogic symbol†1OE1DIR2OE2DIR4812524G33 EN1 [BA]3 EN2 [AB]G66 EN4 [BA]6 EN5 [AB]111221B11A14721B11DIR1 logic diagram (positive logic)1OE481A1471A21A31A41A51A61A71A82A1464443414038373643568911121B21B31B41B51B61B71B82B1To Seven Other Channels2OE25115132A22A32A42A52A62A72A835333230292726141617192022232DIR2B22B32B42B52B62B72B82A12436132B1†This symbol is in accordance with ANSI/IEEE Std 91-1984 andIEC Publication 617-12.To Seven Other Channelsabsolute maximum ratings over operating free-air temperature range (unless otherwise noted)‡Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 VInput voltage range, VI (except I/O ports) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 VVoltage range applied to any output in the high or power-off state, VO . . . . . . . . . . . . . . . . . . . –0.5 V to 5.5 VCurrent into any output in the low state, IO:SN54ABT16640 96 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . mASN74ABT16640. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mAInput clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –18 mAOutput clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mAPackage thermal impedance, θJA (see Note 2):DGG package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89°C/WDL package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94°C/WStorage temperature range, Tstg –65. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . °C to 150°C‡Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, andfunctional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is notimplied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.NOTES:1.The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.2.The package thermal impedance is calculated in accordance with EIA/JEDEC Std JESD51.2POST OFFICE BOX 655303 DALLAS, TEXAS 75265•元器件交易网www.cecb2b.com SN54ABT16640, SN74ABT1664016-BIT BUS TRANSCEIVERSWITH 3-STATE OUTPUTSSCBS107C – APRIL 1992 – REVISED JANUARY 1997recommended operating conditions (see Note 3)SN54ABT16640MINVCCVIHVILVIIOHIOL∆t/∆vSupply voltageHigh-level input voltageLow-level input voltageInput voltageHigh-level output currentLow-level output currentInput transition rise or fall rateOutputs enabled–5504.520.8VCC–244810125–400MAX5.5SN74ABT16640MIN4.520.8VCC–32641085MAX5.5UNITVVVVmAmAns/V°CTAOperating free-air temperatureNOTE 3:Unused pins (input or I/O) must be held high or low to prevent them from floating.POST OFFICE BOX 655303 DALLAS, TEXAS 75265•3元器件交易网www.cecb2b.comSCBS107C – APRIL 1992 – REVISED JANUARY 1997SN54ABT16640, SN74ABT1664016-BIT BUS TRANSCEIVERSWITH 3-STATE OUTPUTS electrical characteristics over recommended operating free-air temperature range (unlessotherwise noted)PARAMETERVIKTESTCONDITIONSTEST CONDITIONSVCC = 4.5 V,VCC = 4.5 V,VCC = 5 V,VCC = 4.5 V=45VVOLVhysIIIOZH‡IOZL‡IoffICEXIO§ICCA or B portsControlinputsA or B portsVCC = 5.5 V,VCC = 5.5 V,VCC = 0,VCC = 5.5 V,VO = 5.5 VVCC = 5.5 V,=5.5V,VCC = 5.5 V,IO = 0,VI = VCC or GNDVCC = 5.5 V,One input at 3.4 V,,Other inputs atVCC or GNDVO = 2.7 VVO = 0.5 VVI or VO ≤ 4.5 VOutputs highVO = 2.5 VOutputs highOutputs lowOutputs disabledOutputs enabledOutputs disabled–50–100,VCC = 5.5 V,VI = VCC or GNDVCC = 4.5 V=45VII = –18 mAIOH = –3 mAIOH = –3 mAIOH = –24 mAIOH = –32 mAIOL = 48 mAIOL = 64 mA100±1±10050–50±10050–180232210.051.53–4050–18023221.50.051.5–50±1±10050–50±1±10050–50±10050–180232210.051.5pFpFmAmAµAµAµAµAmATA = 25°CMINTYP†MAX–1.22.5322*0.550.55*0.550.552.5322VmVµASN54ABT16640MINMAX–1.22.53VSN74ABT16640MINMAX–1.2UNITVVOHDatainptsData inputs∆ICC¶ControlinputsCiCioControlinputsA or B portsVCC = 5.5 V, One input at 3.4 V,Other inputs at VCC or GNDVI = 2.5 V or 0.5 VVO = 2.5 V or 0.5 V8* On products compliant to MIL-PRF-38535, this parameter does not apply.†All typical values are at VCC = 5 V.‡The parameters IOZH and IOZL include the input leakage current.§Not more than one output should be tested at a time, and the duration of the test should not exceed one second.¶This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND.4POST OFFICE BOX 655303 DALLAS, TEXAS 75265•元器件交易网www.cecb2b.com SN54ABT16640, SN74ABT1664016-BIT BUS TRANSCEIVERSWITH 3-STATE OUTPUTSSCBS107C – APRIL 1992 – REVISED JANUARY 1997switching characteristics over recommended ranges of supply voltage and operating free-airtemperature, CL = 50 pF (unless otherwise noted) (see Figure 1)SN54ABT16640PARAMETERFROM(INPUT)TO(OUTPUT)VCC = 5 V,TA = 25°CMINtPLHtPHLtPZHtPZLtPHZtPLZAorBA or BOEOEBorAB or AAorBA or BAorBA or B0.50.50.50.50.50.5TYP2.52.83.53.93.83MAX4.145.266.84.50.50.50.50.50.50.55.24.56.27.47.95nsnsnsMINMAXUNITswitching characteristics over recommended ranges of supply voltage and operating free-airtemperature, CL = 50 pF (unless otherwise noted) (see Figure 1)SN74ABT16640PARAMETERFROM(INPUT)TO(OUTPUT)VCC = 5 V,TA = 25°CMINtPLHtPHLtPZHtPZLtPHZtPLZAorBA or BOEOEBorAB or AAorBA or BAorBA or B11.11.21.51.81.5TYP2.52.83.53.93.83MAX3.43.64.554.83.911.11.21.51.81.54.33.95.56.36.34.2nsnsnsMINMAXUNITPOST OFFICE BOX 655303 DALLAS, TEXAS 75265•5元器件交易网www.cecb2b.comSCBS107C – APRIL 1992 – REVISED JANUARY 1997SN54ABT16640, SN74ABT1664016-BIT BUS TRANSCEIVERSWITH 3-STATE OUTPUTSPARAMETER MEASUREMENT INFORMATION500 ΩS17 VOpenGND500 ΩTESTtPLH/tPHLtPLZ/tPZLtPHZ/tPZHS1Open7 VOpen From Output Under TestCL = 50 pF(see Note A)LOAD CIRCUITtw3 VInput1.5 V1.5 V0 VVOLTAGE WAVEFORMSPULSE DURATION3 VInputtPLHOutputtPHLOutput1.5 V1.5 V1.5 V1.5 V0 VtPHL1.5 VtPLHVOH1.5 VVOLVOLTAGE WAVEFORMSPROPAGATION DELAY TIMESINVERTING AND NONINVERTING OUTPUTSVOHVOL3 VTiming Input1.5 V0 VtsuData Input1.5 VVOLTAGE WAVEFORMSSETUP AND HOLD TIMES3 V1.5 VtPZLOutputWaveform 1S1 at 7 V(see Note B)OutputWaveform 2S1 at Open(see Note B)tPZHtPLZ1.5 VtPHZVOH – 0.3 VVOH≈ 0 VVOLTAGE WAVEFORMSENABLE AND DISABLE TIMESLOW- AND HIGH-LEVEL ENABLING1.5 V0 Vth3 V1.5 V0 VOutputControl3.5 VVOL + 0.3 VVOL1.5 VNOTES:A.CL includes probe and jig capacitance.B.Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.Waveform2 is for an output with internal conditions such that the output is high except when disabled by the output control.C.All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf≤ 2.5 ns.D.The outputs are measured one at a time with one transition per measurement.Figure 1. Load Circuit and Voltage Waveforms6POST OFFICE BOX 655303 DALLAS, TEXAS 75265•元器件交易网www.cecb2b.com

IMPORTANT NOTICE

Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinueany product or service without notice, and advise customers to obtain the latest version of relevant informationto verify, before placing orders, that information being relied on is current and complete. All products are soldsubject to the terms and conditions of sale supplied at the time of order acknowledgement, including thosepertaining to warranty, patent infringement, and limitation of liability.

TI warrants performance of its semiconductor products to the specifications applicable at the time of sale inaccordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extentTI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarilyperformed, except those mandated by government requirements.

CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OFDEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICALAPPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, ORWARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHERCRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TOBE FULLY AT THE CUSTOMER’S RISK.

In order to minimize risks associated with the customer’s applications, adequate design and operatingsafeguards must be provided by the customer to minimize inherent or procedural hazards.

TI assumes no liability for applications assistance or customer product design. TI does not warrant or representthat any license, either express or implied, is granted under any patent right, copyright, mask work right, or otherintellectual property right of TI covering or relating to any combination, machine, or process in which suchsemiconductor products or services might be or are used. TI’s publication of information regarding any thirdparty’s products or services does not constitute TI’s approval, warranty or endorsement thereof.

Copyright © 1998, Texas Instruments Incorporated

因篇幅问题不能全部显示,请点此查看更多更全内容